|
Home::All
Cisco CCNA / CCNP Certification: How And Why To Build An Etherchannel
Author : Chris Bryant, CCIE #12933
CCNA and CCNP candidates are well-versed in Spanning-Tree Protocol, and one of the great things about STP is that it works well with little or no additional configuration. There is one situation where STP works against us just a bit while it prevents switching loops, and that is the situation where two switches have multiple physical connections.
You would think that if you have two separate physical connections between two switches, twice as much data could be sent from one switch to the other than if there was only one connection. STP doesn't allow this by default, however in an effort to prevent switching loops from forming, one of the paths will be blocked.
SW1 and SW2 are connected via two separate physical connections, on ports fast0/11 and fast 0/12. As we can see here on SW1, only port 0/11 is actually forwarding traffic. STP has put the other port into blocking mode (BLK).
SW1#show spanning vlan 10
(some output removed for clarity)
Interface Role Sts Cost Prio.Nbr Type
Fa0/11 Root FWD 19 128.11 P2p
Fa0/12 Altn BLK 19 128.12 P2p
While STP is helping us by preventing switching loops, STP is also hurting us by preventing us from using a perfectly valid path between SW1 and SW2. We could literally double the bandwidth available between the two switches if we could use that path that is currently being blocked.
The secret to using the currently blocked path is configuring an Etherchannel. An Etherchannel is simply a logical bundling of 2 - 8 physical connections between two Cisco switches.
Configuring an Etherchannel is actually quite simple. Use the command "channel-group 1 mode on" on every port you want to be placed into the Etherchannel. Of course, this must be done on both switches if you configure an Etherchannel on one switch and don't do so on the correct ports on the other switch, the line protocol will go down and stay there.
The beauty of an Etherchannel is that STP sees the Etherchannel as one connection. If any of the physical connections inside the Etherchannel go down, STP does not see this, and STP will not recalculate. While traffic flow between the two switches will obviously be slowed, the delay in transmission caused by an STP recalculation is avoided. An Etherchannel also allows us to use multiple physical connections at one time.
Here's how to put these ports into an Etherchannel:
SW1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SW1(config)#interface fast 0/11
SW1(config-if)#channel-group 1 mode on
Creating a port-channel interface Port-channel 1
SW1(config-if)#interface fast 0/12
SW1(config-if)#channel-group 1 mode on
SW2#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SW2(config)#int fast 0/11
SW2(config-if)#channel-group 1 mode on
SW2(config-if)#int fast 0/12
SW2(config-if)#channel-group 1 mode on
The command "show interface trunk" and "show spanning-tree vlan 10" will be used to verify the Etherchannel configuration.
SW2#show interface trunk (some output removed for clarity)
Port Mode Encapsulation Status Native vlan
Po1 desirable 802.1q trunking 1
SW2#show spanning vlan 10 (some output removed for clarity)
Interface Role Sts Cost Prio.Nbr Type
Po1 Desg FWD 12 128.65 P2p
Before configuring the Etherchannel, we saw individual ports here. Now we see "Po1", which stands for the interface "port-channel1". This is the logical interface created when an Etherchannel is built. We are now using both physical paths between the two switches at one time!
That's one major benefit in action let's see another. Ordinarily, if the single open path between two trunking switches goes down, there is a significant delay while another valid path is opened - close to a minute in some situations. We will now shut down port 0/11 on SW2 and see the effect on the etherchannel.
SW2#conf t
Enter configuration commands, one per line. End with CNTL/Z.
SW2(config)#int fast 0/11
SW2(config-if)#shutdown
3w0d: %LINK-5-CHANGED: Interface FastEthernet0/11, changed
state to administratively down
SW2#show spanning vlan 10
VLAN0010
Spanning tree enabled protocol ieee
Interface Role Sts Cost Prio.Nbr Type
Po1 Desg FWD 19 128.65 P2p
SW2#show interface trunk
Port Mode Encapsulation Status Native vlan
Po1 desirable 802.1q trunking 1
The Etherchannel did not go down! STP sees the Etherchannel as a single link therefore, as far as STP is concerned, nothing happened.
Building an Etherchannel and knowing how it can benefit your network is an essential skill for CCNA and CCNP success, and it comes in very handy on the job as well. Make sure you are comfortable with building one before taking Cisco's exams!
Article Source: http://www.articledashboard.com
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage (www.thebryantadvantage.com), home of free http://www.thebryantadvantage.com/">CCNA and CCNP tutorials, The Ultimate CCNA Study Package, and Ultimate CCNP Study Packages. Video courses and training, binary and subnetting help, and corporate training are also available. Pass the http://www.thebryantadvantage.com/UltimateCCNAStudyPackage.html">CCNA exam with Chris Bryant, CCIE #12933!
For a copy of his FREE "How To Pass The CCNA" or "How To Pass The CCNP" ebook, write to chris@thebryantadvantage.com!
Spam emails More free articles Related articles
|
More related feeds |
Cisco CCNA / CCNP Certification: How And Why To Build An Etherchannel
Visit his blog and sign up for Cisco Certification Central, a daily newsletter packed with CCNA, Network+, Security+, A+, and CCNP certification exam practice questions! A free 7-part course, "How To Pass The CCNA", is also available, ...Cbt Cisco CCNP - Exam-Pack: 642-812 BCMSN
In addition, the training maps to exam objectives for Cisco CCNP Exam 642-812 BCMSN, to help you prepare for CCNP Certification. Prerequisites. A thorough understanding of Cisco networking such as a CCNA certification or equivalent ... Cisco CCNA, CCNP, and CCNET Practice Questions - Etherchannels ...
You can also visit his blog, which is updated several times daily with new Cisco certification articles, free tutorials, and daily CCNA / CCNP exam questions! A free 7-part course, “How To Pass The CCNA”, is also available. Earn your ... Cisco CCNA /CCNP Home Lab Tutorial: A Guide To Cable Types
Once you’ve added multiple routers and switches to your CCNA / CCNP home lab, you’ll get tired of moving that rolled cable around. An access server (a special model of Cisco router, actually) will allow you to connect the rolled cable ... Cisco CCNA CCNP Certification How And Why To Build An Etherchannel
CCNA and CCNP candidates are well-versed in Spanning-Tree Protocol, and digit of the enthusiastic things most atm is that it entireness substantially with lowercase or no added configuration. There is digit status where atm entireness ... Cisco Certification Building Your Home Lab Part II
In the prototypal conception of this bag impact tutorial, CCNA and CCNP candidates crapper wager that there are a LOT of choices when it comes to what to take to physique your possess Cisco training lab. Having been there myself, ... Cisco CCNA / CCNP Certification: How And Why To Build An Etherchannel
Building an Etherchannel and knowing how it can benefit your network is an essential skill for CCNA and CCNP success, and it comes in very handy on the job as well. Make sure you are comfortable with building one before taking Cisco’s ... Steve, Wednesday's Mastermind Mail Is Here!
The Ultimate CCNA Study Package The Ultimate CCNP Study Package Bundle All downloadable in minutes, and all 100% satisfaction guaranteed! I'm ready to help you build a brighter future by coaching you all the way to your Cisco ... Steve, Cisco Certification Is Within Your Grasp!
"B" describes an Etherchannel. Answer "D" is incorrect since VTP Clients cannot create and delete VLANs. CCNA Security Certification / CCNP ISCW Exam: You're configuring IPS and have not specified an ACL to filter traffic. ... Cisco CCNA, CCNP, and CCENT Practice Questions: Etherchannels, BGP ...
CCNP Certification / BCMSN Exam: What's the maximum number of physical channels that can be placed into an Etherchannel? Answer: Eight. CCNP Certification / ONT Exam: What's the full command for doubling the capacity of the default ...
|
|
|
